Forum Input for Suppressors
- Rapier1772
- Global Moderator
- Posts: 12939
- Joined: 20 Aug 2008, 09:00
- Location: Benton City, WA
Re: Forum Input for Cans
2.9 of 3N37? Any issues with case volume? That is one of the powders/loads I am experimenting with.
How to post pics & videos: viewtopic.php?f=3&t=6363
Contrary to popular belief, you CAN fix stupid - it's just illegal.
Re: Forum Input for Cans
Not so far. This is what I use for my SBR & pistol--NOT a full legnth 16" barrel--you might get a round stuck!
All legal statements about this load being used in my firearms, etc. apply.
All legal statements about this load being used in my firearms, etc. apply.
- Rapier1772
- Global Moderator
- Posts: 12939
- Joined: 20 Aug 2008, 09:00
- Location: Benton City, WA
Re: Forum Input for Cans
Great, thanks. I don't use any of my reloads in the PS90 as yet. Just the FsN.
Guess I will start dialing it down then. I am at 3.4gr now & using different bullet weights. This powders has proven to have more consistent speed & groups. I like but still get the occasional keyhole
Guess I will start dialing it down then. I am at 3.4gr now & using different bullet weights. This powders has proven to have more consistent speed & groups. I like but still get the occasional keyhole
How to post pics & videos: viewtopic.php?f=3&t=6363
Contrary to popular belief, you CAN fix stupid - it's just illegal.
-
- Junior Member
- Posts: 152
- Joined: 27 Mar 2011, 08:57
Re: Forum Input for Cans
I have an Osprey .45 suppressor that I purchased and have been waiting for as I jump through the NFA hoops.
My question is: As this can is rated for use with the 9mm through .45, do I have to go through the whole process if I want another baffle, so it is interchangable for different calibers or even different guns (i.e. going from my USP Tactical to FNP 45 T)?
My guess is yes, as this is considered a suppressor part, but is it the same waiting period or can I pay the $200 tax and be done with it?
My question is: As this can is rated for use with the 9mm through .45, do I have to go through the whole process if I want another baffle, so it is interchangable for different calibers or even different guns (i.e. going from my USP Tactical to FNP 45 T)?
My guess is yes, as this is considered a suppressor part, but is it the same waiting period or can I pay the $200 tax and be done with it?
Re: Forum Input for Cans
If you want to put it on a 9mm, you will need a different booster since they are different threads. But no you dont need to go through the stamps and paper work again.
-
- Junior Member
- Posts: 152
- Joined: 27 Mar 2011, 08:57
Re: Forum Input for Cans
I was looking through the Silencerco website and I did not see anything about buying different boosters. Maybe there is some adapter I am unaware of.
They do sell different pistons, which adapt to different calibers, but this would qualify as a suppressor part and additional tax stamp in my understanding of NFA laws.
Someone please correct me if I'm wrong...
They do sell different pistons, which adapt to different calibers, but this would qualify as a suppressor part and additional tax stamp in my understanding of NFA laws.
Someone please correct me if I'm wrong...
Re: Forum Input for Cans
Piston and booster are the same thing. Again, when you buy another piston, you don't need another stamp or do the paperwork again
Re: Forum Input for Cans
got my replaced quietor ammo, shot it through the ps90 with the Silencerco Sparrow 22: the rating is still at 2, closer to 3. It's like shooting a 22 lr, easy on the ears, also fine for shooting standard non-subsonic ammo through without ear protection.
Bottom line, this can doesn't get you that total suppression that everyone craves, but it is the perfect can to have for the shooting range, don't have to bother with ear protection (nice thing if you plan on using it for home defense), easily disassembled for cleaning. I have designed a locking quick connector for this can, it is still waiting to be machined, will share pics when that is done.
Bottom line, this can doesn't get you that total suppression that everyone craves, but it is the perfect can to have for the shooting range, don't have to bother with ear protection (nice thing if you plan on using it for home defense), easily disassembled for cleaning. I have designed a locking quick connector for this can, it is still waiting to be machined, will share pics when that is done.
Re: Forum Input for Cans
Has anyone tried or heard anything about this DeGroat Tactical "NANO" suppressor? I'm looking for a can for my FsN and all I seem to hear is negatives about everything out there. I sent a message to David at Liberty Suppressors to see if they had any plans for making a can, and Stu called me back the next business day. Seems they have a huge back log just trying to keep up with existing orders, and until they get caught up, they wont be doing any special projects. So if anyone out there has heard anything about this little suppressor, let us know!!
Thanks!
Thanks!
Re: Forum Input for Cans
I have the AAC M4 2000. Has anyone used it or knows someone? It is great on my AR's but have not got home to try it!
- blueorison
- Competition/Training Mod
- Posts: 10672
- Joined: 11 Apr 2009, 14:28
- custom title: UT/EA Pistol Captain
- Contact:
Re: Forum Input for Cans
yarly I like it.bud1959 wrote:I have the AAC M4 2000. Has anyone used it or knows someone? It is great on my AR's but have not got home to try it!
Never attribute to malice that which can be explained by stupidity.
The shooter will always matter more than the gear ever will.
Stop relying on others to do the work for you.
Shoot more, worry less.
The shooter will always matter more than the gear ever will.
Stop relying on others to do the work for you.
Shoot more, worry less.
Re: Forum Input for Cans
Works well on your PS?
- blueorison
- Competition/Training Mod
- Posts: 10672
- Joined: 11 Apr 2009, 14:28
- custom title: UT/EA Pistol Captain
- Contact:
Re: Forum Input for Cans
Apologies, wasn't clear on what was being asked.
I do not own either, have used the AAC on an AR carbine and seen it used on a AR57. It is hearing safe on the AR57, for me, from a distance of 10 feet. And I have very sensitive ears. Have not used it on a PS90.
Pretty sure Spacecoyote has both; you might want to PM him. Though I don't think his PS90SBR uses it.
I do not own either, have used the AAC on an AR carbine and seen it used on a AR57. It is hearing safe on the AR57, for me, from a distance of 10 feet. And I have very sensitive ears. Have not used it on a PS90.
Pretty sure Spacecoyote has both; you might want to PM him. Though I don't think his PS90SBR uses it.
Never attribute to malice that which can be explained by stupidity.
The shooter will always matter more than the gear ever will.
Stop relying on others to do the work for you.
Shoot more, worry less.
The shooter will always matter more than the gear ever will.
Stop relying on others to do the work for you.
Shoot more, worry less.
Re: Forum Input for Cans
I'm awaiting a mount to put my Spectre on my ps90 and an EA threaded barrel for my fsn.
كاف
Re: Forum Input for Cans
Has any one tried the YHM Phantom Ti on a 5.7 SBR??? Works great on my .223 - 16" (subsonic Ammo) - Just wondering.
- jgreenberg01
- Platinum Member
- Posts: 3737
- Joined: 17 Jul 2009, 14:32
- custom title: FNP-45 Cylon
- Location: Palm Coast, FL
- Contact:
Re: Forum Input for Cans
Yes. Look at this video:WolfRulz wrote:Has any one tried the YHM Phantom Ti on a 5.7 SBR??? Works great on my .223 - 16" (subsonic Ammo) - Just wondering.
0100001101101111011011010110010100100000011000010110111001100100001000000111010001100001011010110110010100100000011010010111010000101110
Re: Forum Input for Cans
My test results - on the YHM Phantom Ti on an AR57 SBR is a rating of 4 (firing SS197). I have basicaly the same setup as jgreenberg01 (nice video - thanks).
It does make a distinctive 'swishing-ping' sound - I think that's the bullet breaking the sound barrier just as it exits and it's quickly followed by the 'SLAP' of the bullet hitting the backstop. I noticed that the Phantom gets hot - REAL HOT after running 50 rounds thru it - I use a silicon pot holder (a dimpled square, good grip and fits nicely in my range bag) to remove it and it does take a while to cool down enough to put it in it's storage bag :laugh:
I'm now reloading my own 40gr Vmax successfully so I'm ready to try creating some subsonics.
It does make a distinctive 'swishing-ping' sound - I think that's the bullet breaking the sound barrier just as it exits and it's quickly followed by the 'SLAP' of the bullet hitting the backstop. I noticed that the Phantom gets hot - REAL HOT after running 50 rounds thru it - I use a silicon pot holder (a dimpled square, good grip and fits nicely in my range bag) to remove it and it does take a while to cool down enough to put it in it's storage bag :laugh:
I'm now reloading my own 40gr Vmax successfully so I'm ready to try creating some subsonics.
Let the Zombies come . . . . .
-
- Junior Member
- Posts: 152
- Joined: 27 Mar 2011, 08:57
Re: Forum Input for Cans
I don't know if anyone saw this yet:
Silencerco's new saker 5.56 suppressor
I own the Osprey 45 suppressor for my USP tactical, which is top notch, so I will be picking up one of these.
I am actually in the market for a 7.62 can that doubles as my 5.56, but I expect the 7.62 at next years SHOT show. If they released the 7.62 first, no one would buy the 5.56.
I like how both ends of the can are adaptable and the flash hider eliminates resonance.
Silencerco's new saker 5.56 suppressor
I own the Osprey 45 suppressor for my USP tactical, which is top notch, so I will be picking up one of these.
I am actually in the market for a 7.62 can that doubles as my 5.56, but I expect the 7.62 at next years SHOT show. If they released the 7.62 first, no one would buy the 5.56.
I like how both ends of the can are adaptable and the flash hider eliminates resonance.
Re: Forum Input for Cans
Guys, yes I am new and thus asking stupid questions you pros have heard a hundred times! Thanks ahead of time
I won a Sparrow22 with the $200 for the tax stamp! I will be submitting the proper paperwork and of course the dealer will hold my suppressor until then...
guys i need to find out how to put this can on my soon to pick up five seven pistol :cya: :cya: posting.php?mode=reply&f=17&t=8215#
1) do in need to buy drop in barrel and get it modded
2) should I get my original barrel modded
3) who should do the work and avg cost?
4) will the Sparrow below with 1/2 x28 threads go on without additional adapter
PS: I own the ruger tactical 10/22 which comes threaded from factory and ruger charger 10/22, fun and cheap plinkers for my boys and I
PLUS my fav, PS90, which I hope to officially (batfe paperwork)convert to shortened/threaded barrel at a later time.
specs!
Silencerco - 22 Sparrow SS
Caliber
.22 lr
Additional Calibers
.17 hmr
.22 mag
.22 wmr
5.7×28 FN
Multi Caliber Use
The stainless steel 22Sparrow is rated and warrantied for use with all rimfire rounds, .22 diam and under such as .17 hmr and .22 mag. It is also rated for use with the 5.7×28 FN round.
Full Auto Use
The 22Sparrow is rated for full auto .22 lr machine guns.
Weight
6.5 oz
Diameter
1.062"
Length
5.08"
Sound reduction
41dB*
* tested with Walther P22, CCI Standard Velocity, 70 degrees, 5100' elevation.
Material
Alloy Steel
Heat Treated 17-4 PH Stainless Steel
Finish
Black Oxide
Magnesium Phosphate (Outer Tube)
Mount
½×28 threads
Thread Options
Don't engage o-ring
Thread should be standard .5×28tpi Class 3A threads with a length of .400"
Engage o-ring
Our innovative Sparrow O-ring engagement offers the additional advantage of keeping the muzzle threads of the host weapon clean and the suppressor is held secure with an o-ring placed inside the female threads to which the host weapon would thread. Silencerco offers custom adapters for the Walther P-22, The Sig Mosquito, the GSG 1911/22 to take advantage of the o-ring engagement. Note: The 22Sparrow will thread on any standard .5×28 threads and any other silencer threaded in .5×28 will thread on our adapters. Minimum overall thread and o-ring engagement is .476".
The 22Sparrow is the first silencer in the world to offer the patent pending Multi Part Containment (MPC) technology, which allows the 22Sparrow to be easily disassembled for cleaning and maintenance after heavy use.
I won a Sparrow22 with the $200 for the tax stamp! I will be submitting the proper paperwork and of course the dealer will hold my suppressor until then...
guys i need to find out how to put this can on my soon to pick up five seven pistol :cya: :cya: posting.php?mode=reply&f=17&t=8215#
1) do in need to buy drop in barrel and get it modded
2) should I get my original barrel modded
3) who should do the work and avg cost?
4) will the Sparrow below with 1/2 x28 threads go on without additional adapter
PS: I own the ruger tactical 10/22 which comes threaded from factory and ruger charger 10/22, fun and cheap plinkers for my boys and I
PLUS my fav, PS90, which I hope to officially (batfe paperwork)convert to shortened/threaded barrel at a later time.
specs!
Silencerco - 22 Sparrow SS
Caliber
.22 lr
Additional Calibers
.17 hmr
.22 mag
.22 wmr
5.7×28 FN
Multi Caliber Use
The stainless steel 22Sparrow is rated and warrantied for use with all rimfire rounds, .22 diam and under such as .17 hmr and .22 mag. It is also rated for use with the 5.7×28 FN round.
Full Auto Use
The 22Sparrow is rated for full auto .22 lr machine guns.
Weight
6.5 oz
Diameter
1.062"
Length
5.08"
Sound reduction
41dB*
* tested with Walther P22, CCI Standard Velocity, 70 degrees, 5100' elevation.
Material
Alloy Steel
Heat Treated 17-4 PH Stainless Steel
Finish
Black Oxide
Magnesium Phosphate (Outer Tube)
Mount
½×28 threads
Thread Options
Don't engage o-ring
Thread should be standard .5×28tpi Class 3A threads with a length of .400"
Engage o-ring
Our innovative Sparrow O-ring engagement offers the additional advantage of keeping the muzzle threads of the host weapon clean and the suppressor is held secure with an o-ring placed inside the female threads to which the host weapon would thread. Silencerco offers custom adapters for the Walther P-22, The Sig Mosquito, the GSG 1911/22 to take advantage of the o-ring engagement. Note: The 22Sparrow will thread on any standard .5×28 threads and any other silencer threaded in .5×28 will thread on our adapters. Minimum overall thread and o-ring engagement is .476".
The 22Sparrow is the first silencer in the world to offer the patent pending Multi Part Containment (MPC) technology, which allows the 22Sparrow to be easily disassembled for cleaning and maintenance after heavy use.
Last edited by garzaro on 05 Mar 2012, 19:06, edited 1 time in total.
Re: Forum Input for Cans
you dont need to hurry and get a barrel. the stamp wont be approved for at least 6 months. some people choose to get a new barrel, others choose to get their stock barrel threaded. along with the threading, you will need a custom adaptor to convert it from 10x1m to silencerco's 1/2x28 o ring threads.
Re: Forum Input for Cans
thank you, will the adapter add much length to the already extended threaded barrel? any suggestions for who you would recommend for the job?
Re: Forum Input for Cans
Yes it will add length. I don't have my fsn threaded so I can't recommend anyone personally
Re: Forum Input for Cans
I can verify the SWR Spectre sounds great on my SBR PS90. I don't really hear much first round pop, and to me the sound is 3 - 4 with subsonics, both the QuiTor and my own homerolled 55gr SP subs.
Onyx
Onyx
-
- Junior Member
- Posts: 21
- Joined: 09 Mar 2010, 13:00
Re: Forum Input for Cans
Well boys, I suppose I will have to finally post a photo of my proprietary reflex suppressor for the PS 90 I designed and built. The platform is a standard 16 inch barrel PS 90 with a quick detach (1/4 turn) titanium suppressor which slides over the entire barrel and has the look of a P90 with a screw on unit. It's very quiet with sub-sonic ammo, pop gun sound, and with supersonic ammo, shooting without hearing protection is very comfortable... love it!
- Esteves
- Wiki Moderator
- Posts: 3168
- Joined: 20 Aug 2008, 10:23
- custom title: Shhh!
- Location: Tucson, AZ
Re: Forum Input for Cans
Pics (or video), or it ain't true.slimpikins wrote:Well boys, I suppose I will have to finally post a photo of my proprietary reflex suppressor for the PS 90 I designed and built. The platform is a standard 16 inch barrel PS 90 with a quick detach (1/4 turn) titanium suppressor which slides over the entire barrel and has the look of a P90 with a screw on unit. It's very quiet with sub-sonic ammo, pop gun sound, and with supersonic ammo, shooting without hearing protection is very comfortable... love it!
--
S
© 2004-2019 Esteves
Political tags — such as royalist, communist, democrat, populist, fascist, liberal, conservative,
and so forth — are never basic criteria. The human race divides politically into those who want
people to be controlled and those who have no such desire.
S
© 2004-2019 Esteves
Political tags — such as royalist, communist, democrat, populist, fascist, liberal, conservative,
and so forth — are never basic criteria. The human race divides politically into those who want
people to be controlled and those who have no such desire.
- panzermk2
- Forum Supporter
- Posts: 12380
- Joined: 19 Aug 2008, 15:51
- Location: Pr. CEO Elite Ammunition
- Contact:
Re: Forum Input for Cans
Esteves wrote:Pics (or video), or it ain't true.slimpikins wrote:Well boys, I suppose I will have to finally post a photo of my proprietary reflex suppressor for the PS 90 I designed and built. The platform is a standard 16 inch barrel PS 90 with a quick detach (1/4 turn) titanium suppressor which slides over the entire barrel and has the look of a P90 with a screw on unit. It's very quiet with sub-sonic ammo, pop gun sound, and with supersonic ammo, shooting without hearing protection is very comfortable... love it!
If this is who I think it is they have been using some of our SS 16.5 to test.
Jay Wolf
Pr. Elite Ammunition
Pr. Elite Ammunition
"Engineers, the oompa-loompas of science!"
Be'ein Tachbulot Yipol Am Veteshua Berov Yoetz
-
- Junior Member
- Posts: 21
- Joined: 09 Mar 2010, 13:00
Re: Forum Input for Cans
The reflex suppressor is a pop gun with FN sub-sonic ammo, however the ammo is VERY dirty causing fouling in the barrel and bolt. I suspect this might well be due to its being designed for use in a 10 inch barrel and the longer 16 inch barrel traps too much debris. It caused a bullet to jam in the barrel and get slammed by a following round. Not good.
After removal of the jammed bullets, I went over to using stock super-sonic ammo, blue tip variety and not one problem. It's obviously a little louder, however no hearing protection is required and it's much quieter than a standard .22LR round. I tried some of the sub-sonic rounds offered by Elite Ammo in the two loads produced, but neither were sub sonic as clocked by the Chronograph and hence about the same noise as standard blue tip. I don't know why this is, perhaps it's due to the factory 16 inch barrel.
I feel this set up is fantastic for use with standard ammo, which is much less costly and is usable without any hearing protection and yet has full velocity vs. sub-sonic. I am very pleased with this system. Plus the suppressor is on a quick detach mounting at the receiver end, so breakdown after use for cleaning is a matter of 2 seconds.
After removal of the jammed bullets, I went over to using stock super-sonic ammo, blue tip variety and not one problem. It's obviously a little louder, however no hearing protection is required and it's much quieter than a standard .22LR round. I tried some of the sub-sonic rounds offered by Elite Ammo in the two loads produced, but neither were sub sonic as clocked by the Chronograph and hence about the same noise as standard blue tip. I don't know why this is, perhaps it's due to the factory 16 inch barrel.
I feel this set up is fantastic for use with standard ammo, which is much less costly and is usable without any hearing protection and yet has full velocity vs. sub-sonic. I am very pleased with this system. Plus the suppressor is on a quick detach mounting at the receiver end, so breakdown after use for cleaning is a matter of 2 seconds.
- panzermk2
- Forum Supporter
- Posts: 12380
- Joined: 19 Aug 2008, 15:51
- Location: Pr. CEO Elite Ammunition
- Contact:
Re: Forum Input for Cans
Have you tried our barrel specific sub sonic ammo? I just reformulated the 10.5 to reduce residue.
Jay Wolf
Pr. Elite Ammunition
Pr. Elite Ammunition
"Engineers, the oompa-loompas of science!"
Be'ein Tachbulot Yipol Am Veteshua Berov Yoetz
Re: Forum Input for Cans
finally got my FsN threaded. Liberty Kodiak and my normal supersonic reloads. No need for hearing protection. Works great.
- panzermk2
- Forum Supporter
- Posts: 12380
- Joined: 19 Aug 2008, 15:51
- Location: Pr. CEO Elite Ammunition
- Contact:
Re: Forum Input for Cans
jmz5 wrote:I need to get me a threaded barrel...
Do you know someone who can get you one? :p
Jay Wolf
Pr. Elite Ammunition
Pr. Elite Ammunition
"Engineers, the oompa-loompas of science!"
Be'ein Tachbulot Yipol Am Veteshua Berov Yoetz
- jgreenberg01
- Platinum Member
- Posts: 3737
- Joined: 17 Jul 2009, 14:32
- custom title: FNP-45 Cylon
- Location: Palm Coast, FL
- Contact:
Re: Forum Input for Cans
Panic cruise buying...
0100001101101111011011010110010100100000011000010110111001100100001000000111010001100001011010110110010100100000011010010111010000101110
Re: Forum Input for Cans
I need a threaded barrel as well. I wonder how well an Osprey would work on 5.7
- panzermk2
- Forum Supporter
- Posts: 12380
- Joined: 19 Aug 2008, 15:51
- Location: Pr. CEO Elite Ammunition
- Contact:
Re: Forum Input for Cans
Buffman wrote:I need a threaded barrel as well. I wonder how well an Osprey would work on 5.7
It's OK the Gemtech is the best I have found so far. Size, weight etc. it strikes the best balance.
Jay Wolf
Pr. Elite Ammunition
Pr. Elite Ammunition
"Engineers, the oompa-loompas of science!"
Be'ein Tachbulot Yipol Am Veteshua Berov Yoetz
Re: Forum Input for Cans
people have used an Osprey 45 can on a 5.7? I was joking, as I didn't think it could handle the pressure
Re: Forum Input for Cans
Of course it can. between the volume/bore size, it can handle tons of sub calibers. Pressure isnt the only thing a suppressor needs to worry about, volume is the other. The 5.7x28 doesn't have a lot of volume. Thats why quite a few .22 suppressors can handle it. The Osprey .45 is also rated for 10mm.
- jgreenberg01
- Platinum Member
- Posts: 3737
- Joined: 17 Jul 2009, 14:32
- custom title: FNP-45 Cylon
- Location: Palm Coast, FL
- Contact:
Re: Forum Input for Cans
I will have a Spectre II whenever the ATF gets around to approving the tax stamp (they say March-ish). I got it for my Ruger 10/22 & S&W M&P22 but it's multi-caliber so I'll also track down a threaded barrel for the FsN when I get the suppressor and we'll see how that one works.
It had the best average sound reduction while maintaining the best accuracy of these cans that were tested:
http://www.americanrifleman.org/article ... Silencerco" onclick="window.open(this.href);return false;
EDIT: Jay - I just noticed that as per your website there's a 10-12 week lead time on the threaded barrels - I don't know if you can even answer this, but with all the panic buying going on, is this still a reasonable estimate for ETA?
It had the best average sound reduction while maintaining the best accuracy of these cans that were tested:
http://www.americanrifleman.org/article ... Silencerco" onclick="window.open(this.href);return false;
EDIT: Jay - I just noticed that as per your website there's a 10-12 week lead time on the threaded barrels - I don't know if you can even answer this, but with all the panic buying going on, is this still a reasonable estimate for ETA?
0100001101101111011011010110010100100000011000010110111001100100001000000111010001100001011010110110010100100000011010010111010000101110
- panzermk2
- Forum Supporter
- Posts: 12380
- Joined: 19 Aug 2008, 15:51
- Location: Pr. CEO Elite Ammunition
- Contact:
Re: Forum Input for Cans
jgreenberg01 wrote:I will have a Spectre II whenever the ATF gets around to approving the tax stamp (they say March-ish). I got it for my Ruger 10/22 & S&W M&P22 but it's multi-caliber so I'll also track down a threaded barrel for the FsN when I get the suppressor and we'll see how that one works.
It had the best average sound reduction while maintaining the best accuracy of these cans that were tested:
http://www.americanrifleman.org/article ... Silencerco" onclick="window.open(this.href);return false;
EDIT: Jay - I just noticed that as per your website there's a 10-12 week lead time on the threaded barrels - I don't know if you can even answer this, but with all the panic buying going on, is this still a reasonable estimate for ETA?
No damn clue.
Jay Wolf
Pr. Elite Ammunition
Pr. Elite Ammunition
"Engineers, the oompa-loompas of science!"
Be'ein Tachbulot Yipol Am Veteshua Berov Yoetz
-
- Junior Member
- Posts: 44
- Joined: 26 Aug 2012, 22:52
Re: Forum Input for Cans
My Sparrow takes the bite out of the pistol, but not hearing safe (imo). My Mystic, although big, cycles fine and is hearing safe. Have not tried my Osprey yet.
-
- Junior Member
- Posts: 213
- Joined: 26 Jan 2010, 22:37
- custom title: Concrete Jungle
- Location: Tulsa,OK.
Re: Forum Input for Cans
I have the AAC Ti Rant 45 and its really quiet and when you shoot it wet its scary quiet, I thought it would be front heavy but with a full mag it evens out and the tall Heine tactical night sights aiming isn't a problem. I've heard cap guns that are twice as loud. I love it and use it on my HK 45c and vector super v cqb.
Re: Forum Input for Cans
I have a Thunderbeast 22-L1. I've only used SS195LF so far. The suppression was fantastic. Most of the noise I heard was coming from round hitting the target. Only firing this from my FiveseveN pistol though I felt unacceptable amounts of blowback. I'd give this a 3 for the sound but a 0 for the blowback. I'm considering a 9mm suppressor or perhaps larger.
- panzermk2
- Forum Supporter
- Posts: 12380
- Joined: 19 Aug 2008, 15:51
- Location: Pr. CEO Elite Ammunition
- Contact:
Re: Forum Input for Cans
Cool thank you for the feed back since it's pretty much impossible for one person to have every can out there just for testing.offtheace wrote:I have a Thunderbeast 22-L1. I've only used SS195LF so far. The suppression was fantastic. Most of the noise I heard was coming from round hitting the target. Only firing this from my FiveseveN pistol though I felt unacceptable amounts of blowback. I'd give this a 3 for the sound but a 0 for the blowback. I'm considering a 9mm suppressor or perhaps larger.
Jay Wolf
Pr. Elite Ammunition
Pr. Elite Ammunition
"Engineers, the oompa-loompas of science!"
Be'ein Tachbulot Yipol Am Veteshua Berov Yoetz
-
- Junior Member
- Posts: 5
- Joined: 26 Jul 2013, 17:42
- Location: Lancaster, Pennsyltucky
Re: Forum Input for Cans
Has anyone tried an AAC Element 2 on a FSN pistol?
Re: Forum Input for Cans
Hey guys whats the best can for the ps90 SBR for quick detach mount?
- Rapier1772
- Global Moderator
- Posts: 12939
- Joined: 20 Aug 2008, 09:00
- Location: Benton City, WA
Re: Forum Input for Cans
For quick detach stuff, Gemtech G5 is pretty good. They also sell the flash hider mate for the PS90
How to post pics & videos: viewtopic.php?f=3&t=6363
Contrary to popular belief, you CAN fix stupid - it's just illegal.
- Rapier1772
- Global Moderator
- Posts: 12939
- Joined: 20 Aug 2008, 09:00
- Location: Benton City, WA
Re: Forum Input for Suppressors
FINALLY got my new suppressor, an Elite Iron Echo for the 5.7. (Which they've apparently discontinued?)
Using subsonic ammo (3.4gr HS-6, 55gr FMJ), it is quieter than my Gemtech. GT was about like a loud paintball gun but still kinda wanted hearing protection. Last night I fired 20rd through the Echo & I don't think it's loud enough to worry about.
I did not try any factory ammo but with supersonic rounds one will likely need to use ear plugs anyway.
Also, the diameter of the suppressor is smaller than I realized. Looking down the sights, I don't notice the suppressor at all; the slide completely obscures it. I'd score it at a 4
It is heavy when compared to the GT & even when compared to the FsN itself.
BATFE wait time: 7 months.
EDIT: Had a friend with the electronic ear muffs on, they didn't activate when I fired subsonics through the Echo.
Using subsonic ammo (3.4gr HS-6, 55gr FMJ), it is quieter than my Gemtech. GT was about like a loud paintball gun but still kinda wanted hearing protection. Last night I fired 20rd through the Echo & I don't think it's loud enough to worry about.
I did not try any factory ammo but with supersonic rounds one will likely need to use ear plugs anyway.
Also, the diameter of the suppressor is smaller than I realized. Looking down the sights, I don't notice the suppressor at all; the slide completely obscures it. I'd score it at a 4
It is heavy when compared to the GT & even when compared to the FsN itself.
BATFE wait time: 7 months.
EDIT: Had a friend with the electronic ear muffs on, they didn't activate when I fired subsonics through the Echo.
How to post pics & videos: viewtopic.php?f=3&t=6363
Contrary to popular belief, you CAN fix stupid - it's just illegal.
Re: Forum Input for Suppressors
Based on yer "7 month" info, GONRA's expecting Gemtech around May.
Interested in your handload! What brass & primer did you use?
Intention was to use the ORIGINAL EA brass - "drastically reduced case capacity"
but am accumlating data needed to blast away when it arrries.
THANX!
Interested in your handload! What brass & primer did you use?
Intention was to use the ORIGINAL EA brass - "drastically reduced case capacity"
but am accumlating data needed to blast away when it arrries.
THANX!
- Rapier1772
- Global Moderator
- Posts: 12939
- Joined: 20 Aug 2008, 09:00
- Location: Benton City, WA
Re: Forum Input for Suppressors
Factory brass & Winchester Small Rifle primers.GONRA wrote: ↑15 Mar 2017, 13:26Based on yer "7 month" info, GONRA's expecting Gemtech around May.
Interested in your handload! What brass & primer did you use?
Intention was to use the ORIGINAL EA brass - "drastically reduced case capacity"
but am accumlating data needed to blast away when it arrries.
THANX!
How to post pics & videos: viewtopic.php?f=3&t=6363
Contrary to popular belief, you CAN fix stupid - it's just illegal.
Re: Forum Input for Suppressors
GONRA received GEMTECH. About 10 months 3 weeks BATF wait tyme. Guesss I'm "Special"?
Hope to blast away next week. Have Fun Fellas.....
Hope to blast away next week. Have Fun Fellas.....
- panzermk2
- Forum Supporter
- Posts: 12380
- Joined: 19 Aug 2008, 15:51
- Location: Pr. CEO Elite Ammunition
- Contact:
Re: Forum Input for Suppressors
Sweet!
Jay Wolf
Pr. Elite Ammunition
Pr. Elite Ammunition
"Engineers, the oompa-loompas of science!"
Be'ein Tachbulot Yipol Am Veteshua Berov Yoetz
Re: Forum Input for Suppressors
GONRA’s first shootin’ with suppressor.
Following setup was a HUGE SUCCESS.
5.7x28mm FN Five-seveN® pistol 20 rd. mag, Viridian Universal Mount Green Laser.
Sights / laser were setup / adjusted with FN’s original barrel.
Try to beat this setup fellas.....
Today used (first time) EA 20 lb. recoil spring and threaded FiveSeveN EFK Fire Dragon barrel
GEMTECH SFN-57 suppressor with 10x1mm metric RH threads.
Shot 5 rounds new factory FNB 14 ammo. Had other shooters shoot 2 more 5 rd. strings
so I could try to figger out where fired cases went and listen to “supersonic suppressed noise”.
STRONG EJECTION, FLAT PRIMERS, MUCH QUIETER.
Found 8 fired cases (looked Just Fine) – remainder are in somewhere in “weed heaven”
after bouncing off sheet metal corrugated roof.
This rough “3 (experienced) shooters 25 yard test” had nice overlapping groups. Maybe 8 inches.
We noted how easy it is (obvious sights, nice trigger pull, no real recoil) to blast away with this setup.
Really pleased, fun to shoot, etc.
Plan on loading up subsonic ammo next, after cleaning up a couple other Pointless Retired Man gun projects.
Following setup was a HUGE SUCCESS.
5.7x28mm FN Five-seveN® pistol 20 rd. mag, Viridian Universal Mount Green Laser.
Sights / laser were setup / adjusted with FN’s original barrel.
Try to beat this setup fellas.....
Today used (first time) EA 20 lb. recoil spring and threaded FiveSeveN EFK Fire Dragon barrel
GEMTECH SFN-57 suppressor with 10x1mm metric RH threads.
Shot 5 rounds new factory FNB 14 ammo. Had other shooters shoot 2 more 5 rd. strings
so I could try to figger out where fired cases went and listen to “supersonic suppressed noise”.
STRONG EJECTION, FLAT PRIMERS, MUCH QUIETER.
Found 8 fired cases (looked Just Fine) – remainder are in somewhere in “weed heaven”
after bouncing off sheet metal corrugated roof.
This rough “3 (experienced) shooters 25 yard test” had nice overlapping groups. Maybe 8 inches.
We noted how easy it is (obvious sights, nice trigger pull, no real recoil) to blast away with this setup.
Really pleased, fun to shoot, etc.
Plan on loading up subsonic ammo next, after cleaning up a couple other Pointless Retired Man gun projects.
Re: Forum Input for Suppressors
When I shot my PS90, I put (150) rounds through it. And I did not need hearing protection at all! It sounded like a .22LR rifle.
I was using American Eagle I’m sure this is why it was so quiet!
Moving to using my Five SeveN and it’s very loud.
I was using American Eagle I’m sure this is why it was so quiet!
Moving to using my Five SeveN and it’s very loud.
Re: Forum Input for Suppressors
So, I know this is an old thread, but Jay wolf brought it up on Facebook, so I figured I would add to it. I bought an Innovative Arms Slingshot TI to use with my 22's and my FiveseveN.
I would add a rating based on the original scale at a 3.
It is quiet with a deep tone. The main thing I don't like about it (and 90%+ of all silencers out there) is that it does not allow for direct thread. I spoke with a company called AB Suppressors and they can make their Little Bird with the thread pitch for the FiveseveN, but it is a special run. I bet if we get enough people to ask about it, they might make one available that is direct thread. I have not heard it on a FiveseveN yet, but I have held one. They are very thin and light. It would be interesting to see how they perform. I might get my buddy to take me out and we can try it on mine.
https://absuppressor.com
I would add a rating based on the original scale at a 3.
It is quiet with a deep tone. The main thing I don't like about it (and 90%+ of all silencers out there) is that it does not allow for direct thread. I spoke with a company called AB Suppressors and they can make their Little Bird with the thread pitch for the FiveseveN, but it is a special run. I bet if we get enough people to ask about it, they might make one available that is direct thread. I have not heard it on a FiveseveN yet, but I have held one. They are very thin and light. It would be interesting to see how they perform. I might get my buddy to take me out and we can try it on mine.
https://absuppressor.com
- panzermk2
- Forum Supporter
- Posts: 12380
- Joined: 19 Aug 2008, 15:51
- Location: Pr. CEO Elite Ammunition
- Contact:
Re: Forum Input for Suppressors
Input added.
Yeah that is the issue with the small FsN barrels. The original Gemtec SFN-57 was one of the few that direct threaded.
Yeah that is the issue with the small FsN barrels. The original Gemtec SFN-57 was one of the few that direct threaded.
Jay Wolf
Pr. Elite Ammunition
Pr. Elite Ammunition
"Engineers, the oompa-loompas of science!"
Be'ein Tachbulot Yipol Am Veteshua Berov Yoetz
Re: Forum Input for Suppressors
I am interested in the "few" if any that will direct thread on my efk 57 pitch?. Even the new gsl tech has adapter..
Who is online
Users browsing this forum: No registered users and 3 guests