REM T3 GD For the Green Dot Fiber Optic

Manufacturer of the Reticle Enhancement Module 3 for the PS90, Illuminates the White Ring Sight,The Black Ring Sight and the Green Dot Fiber Optic Ring Sight.
"Peace Through Strength" merchandise

Moderator: M1P90

Post Reply
User avatar
M1P90
Forum Supporter
Posts: 306
Joined: 20 Aug 2008, 08:19
Location: Socialist Republic of Mass.
Contact:

REM T3 GD For the Green Dot Fiber Optic

Post by M1P90 » 24 Aug 2011, 12:02

The REM T3GD for the PS90 Green Dot Fiber Optic is now available for sale and is in stock. :clap:
The Price is $89.00 shipped. I take Visa, Mastercard and Discover or check or money order. I do also take PAYPAL.
Go to http://WWW.M1Bullpup.com" onclick="window.open(this.href);return false; to pay.

The Reticule Enhancement Module (T-bar) 3GD is to be used as a back up to the Green Dot Ring Sight. Try to rely on the Original Sight when possible.

The Reticule Enhancement Module 3GD (REM T3GD) fixes the problem that is inherent in the Green Dot Ring Sight. We all know in certain low light conditions the Ring Sight looses its sight picture. When that happens just turn on the REM T3GD and you will get a sharp Green Dot sight picture.

The REM T3GD Illuminates the Green Dot Fiber Optic via a White LED that is attached to the underside of the Ring Sight. There needs to be minor drilling and gluing to affix the T3GD to the Sight.

It has 11 illumination settings so the Green Dot can be seen outdoors in daylight (on its brightest setting) or in total darkness (on its lowest setting). The REM T3GD fits in the sling well just under the Ring Sight. It is ambidextrous so it can be mounted on the left or right side of the rifle.

The REM T3GD uses TWO CR2016 3 volt battery.
Since we did not make the Rheostats...
The REM T3GD has a 1 YEAR Warranty. I will replace it if it fails due to a manufacturing problem. (I will have to examine it first to make sure there wasn't some other factor that caused the failure). You just pay for the shipping ($5.00). If after 1 year a manufacturing problem should occur... contact me and I will see what I can do for you.

The REM T3GD comes with a 30 day money back guarantee. If you are dissatisfied with it, please send it back to me and I will give you a full refund. (You just pay the shipping)

The electrical wire will have a metal wire in it so it can be positioned out of your line of sight.

REM T3GD
Image

The REM T3GD Attaches to this FN Green Dot Fiber Optic Sight.
Image

Green Dot Sight Picture Normal
Image

Green Dot Sight Picture with the T3GD set in high #11
Image

Green Dot Sight Picture in a low light room (Normal)
Image

Green Dot Sight Picture with T3GD set on #1
Image

Green Dot Sight Picture with T3GD set on #5
Image
Image

PEACE THROUGH STRENGTH
http://www.M1bullpup.com" onclick="window.open(this.href);return false;

User avatar
M1P90
Forum Supporter
Posts: 306
Joined: 20 Aug 2008, 08:19
Location: Socialist Republic of Mass.
Contact:

Re: REM T3 GD For the Green Dot Fiber Optic

Post by M1P90 » 13 Sep 2011, 04:30

I found it quite interesting that the only color LED that really works on this Fiber Optic is White. Any other color just doesn't illuminate it. :ponder: I will install the REM T3GD for FREE just as I do with the REM T3 for the Black Ring Sight. Here is how to install the REMT3GD.

1) Pry off the bottom base plate with a screwdriver. Go along the entire edge first to break the glue adhesive. Then lift up the 4 prongs (2 on each side) to continue seperating the adhesive. The Plate will eventually pry off.
Image

You will see this. A) Tritium B) Fiber Optic C) Base Plate(Drill a hole here)Widen the hole at the top of the round ring so that the top of the LED is flush with the top of the plastic ring. Dremel a notch in the very back of the Base Plate so the wire will fit in the notch.
Image

See where the Fiber Optic is placed and expand the hole if you need to so that the Fiber Optic is directly under the hole. Replace the Base Plate back onto the Ring Sight then Place the LED in the hole and epoxy it in place and also epoxy the wire into the notch. (WARNING Do not drill the base plate while it is still attached to the Ring Sight. You may damage the Fiber Optic.)
You will have to hold the LED in place with an exacto knife for 10 to 15 minutes. You may have to hold the LED in place a few more minutes if the epoxy has not solidified enough.
6) After 10 to 15 minutes pull out the knife and then use the back flat part of the knife to hold the LED in place until the epoxy solidifies. (another 5 minutes)
7) Let the epoxy dry for another hour before you do anything else.
8 Turn on the T3GD and check for any light leakage through the epoxy. If so you can put some black paint on that area to cover the leakage.
9) Carefully bend the LED wire to the side of the Ring Sight you desire.
Image

Re-Attach the Ring Sight to your PS90 and attach the REM T3GD to the Receiver via the sling well.
Image
Image

PEACE THROUGH STRENGTH
http://www.M1bullpup.com" onclick="window.open(this.href);return false;

User avatar
M1P90
Forum Supporter
Posts: 306
Joined: 20 Aug 2008, 08:19
Location: Socialist Republic of Mass.
Contact:

Re: REM T3 GD For the Green Dot Fiber Optic

Post by M1P90 » 06 Jul 2015, 07:02

:gavel: As of today 7/6/15 all future orders are Backordered about 60 days. I am having aluminum molds made so once the new REMs start coming off the line there will be a price reduction. I am shooting for around $50 each. I'll post the new price once we get closer to full production.

Stay tuned...

Chris
http://www.M1Bullpup.com" onclick="window.open(this.href);return false;
Image

PEACE THROUGH STRENGTH
http://www.M1bullpup.com" onclick="window.open(this.href);return false;

User avatar
M1P90
Forum Supporter
Posts: 306
Joined: 20 Aug 2008, 08:19
Location: Socialist Republic of Mass.
Contact:

Re: REM T3 GD For the Green Dot Fiber Optic

Post by M1P90 » 03 Apr 2016, 05:15

I have stopped taking any new orders of the REM T3s, REM T3Bs and REM T3GDs until I get the new designed REM on the market. It should take about 6 months. I will be filling all backorders within the next months as parts trickle in.
I have found a good Molding company that will mass produce these so the new price point will be around $40. It will take time to get the new molds made and get the production going.
You will love the new REMs and Packaging! :)

Chris
Image

PEACE THROUGH STRENGTH
http://www.M1bullpup.com" onclick="window.open(this.href);return false;

Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests