Page 1 of 2

REM T3b for the Black Ring Sight now on sale

Posted: 07 Jul 2009, 10:57
by M1P90
The REM T3b for the PS90 USG "Black Ring Sight" is now available for sale and is in stock. :clap:
The Price is $89.00 shipped. I take Visa, Mastercard and Discover or check or money order. I do also take PAYPAL.
Go to http://WWW.M1Bullpup.com" onclick="window.open(this.href);return false; to pay.

The Reticule Enhancement Module (T-bar) 3b is to be used as a back up to the Black Ring Sight. Try to rely on the Black Crosshairs when possible.

The Reticule Enhancement Module 3b (REM T3b) fixes the problem that is inherent in the Black Ring Sight. We all know in certain low light conditions the Ring Sight looses its sight picture. When that happens just turn on the REM T3b and you will get a sharp T bar sight picture.

The REM T3b Illuminates the T bar via a colored LED red or green or blue that is attached to the underside of the Ring Sight. There needs to be minor drilling and gluing to affix the T3b to the Sight.

It has 11 illumination settings so the T bar can be seen outdoors in daylight (on its brightest setting) or in total darkness (on its lowest setting). The REM T3b fits in the sling well just under the Ring Sight. It is ambidextrous so it can be mounted on the left or right side of the rifle.

The REM T3b uses one CR2032 3 volt battery. The battery life is 106 hours of continuous use.

Since we did not make the Rheostats...
The REM T3b has a 1 YEAR Warranty. I will replace it if it fails due to a manufacturing problem. (I will have to examine it first to make sure there wasn't some other factor that caused the failure). You just pay for the shipping ($5.00). If after 1 year a manufacturing problem should occur... contact me and I will see what I can do for you.

The REM T3 comes with a 30 day money back guarantee. If you are dissatisfied with it, please send it back to me and I will give you a full refund. (You just pay the shipping)

Black Ring Sight with REM T3b
Image

Standard view of the USG on a cloudy day.
Image


Same view with the REM T3b turned on high.
Image


Standard view of the USG against a black target. (Can't see a thing)
Image


Same view with the REM T3b turned on high. (I can see!) :D
Image


Same view with the REM T3b turned on high (green LED).
Image

Same view with the REM T3b turned on high (blue LED).
Image

Re: REM T3b for the Black Ring Sight coming soon

Posted: 29 Jul 2009, 18:45
by M1P90
USG sight in normal mode.
Image


USG sight with the REM T3b set on #1 (red LED)
Image

USG sight with the REM T3b set on #1 (green LED)
Image

USG sight with the REM T3b set on #1 (blue LED)
Image

Re: REM T3b for the Black Ring Sight coming soon

Posted: 29 Jul 2009, 19:12
by Wollychop
Very cool... Can't wait!

Will this module also be compatible with white reticule sights (i have PS90s with both)?

Re: REM T3b for the Black Ring Sight coming soon

Posted: 29 Jul 2009, 20:33
by Cyberfly
:D
That IS sweet!

Re: REM T3b for the Black Ring Sight coming soon

Posted: 30 Jul 2009, 03:45
by jmz5
That looks awesome.

Re: REM T3b for the Black Ring Sight coming soon

Posted: 30 Jul 2009, 03:48
by M1P90
Wollychop wrote:Very cool... Can't wait!

Will this module also be compatible with white reticule sights (i have PS90s with both)?
No.
The white reticle sight needs the LED housing to fit in the light collection well while the
black reticle sight needs the LED to be permanently attached to the underside. Also, the wire needs to be 1/2 inch longer.

There needs to be a minor operation on the USG sight in order to expose the tritium bar and to attach the LED. Make sure you don't cut too deep or you may damage the glass optic.
I'll do the procedure at no extra cost.

You will need a Dremel and use this tool to drill a hole in the rubber Tritium cover.
Image

You will also need an exacto knife to finish cleaning out the hole to expose the Tritium.
Image

NOW THE FUN STARTS.

1) Cut a small hole the size of the LED and expose the Tritium bar. Be careful not to drill the Tritium. (drill slowly)
Image

2)Make sure the hole is centered.
Image

Image

3) Finish removing debris from hole by cutting the rubber and pulling it out with tweezers.
Image

4) Picture of completed hole.
Image

5) Use 5 minute epoxy to attach T3b to Ring Sight
Image

6) Immobilize the T3b to the Ring Sight and insert the LED into the hole.
Hold it in place with the tip of the exacto knife.
Image

7) While holding the LED in place, Cover the LED and rubber area and part of the metal with the 5 minute epoxy. You will have to hold the LED for 5 minutes.
Image

8) After 5 minutes pull out the knife and then use the back flat part of the knife to hold the LED in place untill the epoxy solidifies. (another 5 munites)
Image

9) Completed process.
Image

10) Carefully bend the LED wire to the side of the Ring Sight you desire.
Image

11) Attach the REM T3b to the rifle and re-attach your Ring Sight.
ALL DONE!!
Image


You can now see the cross hairs in any light condition and against any background. :shock:

Re: REM T3b for the Black Ring Sight coming soon

Posted: 30 Jul 2009, 06:53
by Esteves
Nice!

Re: REM T3b for the Black Ring Sight coming soon

Posted: 24 Aug 2009, 11:24
by Merlin
Newbie here. :p Are you still on schedule for the end of September release? Thanks.

Re: REM T3b for the Black Ring Sight coming soon

Posted: 25 Aug 2009, 03:10
by M1P90
Merlin wrote:Newbie here. :p Are you still on schedule for the end of September release? Thanks.
So far so good. Image

11/14/09 The REM T3b is now in stock!!!! :drool:

Re: REM T3b for the Black Ring Sight coming soon

Posted: 25 Aug 2009, 18:59
by Merlin
M1P90 wrote:
Merlin wrote:Newbie here. :p Are you still on schedule for the end of September release? Thanks.
So far so good. Image

I do have 10 units available right now. But thats it until I receive more parts.

let me know if you want one of those.
Yes, I am interested. Will have to wait until I receive the PS90 though, want to make sure what I have so I get the correct version. Thanks.

Re: REM T3b for the Black Ring Sight coming soon

Posted: 06 Oct 2009, 10:43
by M1P90
REM T3b Instruction Manual

Thank you for purchasing this upgrade to your PS90 Ring Sight. The REM T3b was designed to maximize your shooting pleasure by fixing the deficiencies of the Ring Sight.

Image

Installation
1) Carefully bend the LED wire
to the side of the Ring Sight you prefer.
2) Place the dialed rheostat on one side of the Sling Well and the small holder on the other side. Tighten the mounting screws until both sides are secure. Use the Allen wrench that is supplied for this procedure. (DO NOT OVER-TIGHTEN) to prevent damage to the screw pins. You can use BLUE thread locker if you like but it is not necessary.
3) Re-attach your Ring Sight to the PS90.

Image


You can now turn on and use the REM T3b.


NOTE: The REM T3b does not interfere with the Tritium Bar so in total darkness you can still rely on that as a light source if desired.

NOTE: When using the REM T3b in total darkness, with no tactical lights in use, you may notice a slight glow on the front optic glass within short distances (less than 10 feet.) This does not interfere with use of the REM T3b.

Battery Replacement
Hold the “numbered part” of the Rheostat so it doesn’t turn. Turn the outside Rheostat battery cover counter clockwise to remove cover. The REM T3b uses one Lithium 3volt CR2032 battery. This package contains ONE spare battery for your convenience.

Warranty
This Product is warranted against original defects in material and/or manufacturing for one year. This warranty is void if the unit has been abused, disassembled, or modified/tampered with in any way from its original configuration.

This warranty does not apply to defects caused by normal wear and tear, improper handling, incorrect installation, accidents, and alterations/modifications to the original configuration, repairs made by unauthorized parties, aftermarket accessories, or abnormal use.

Contact Us
We hope you find the REM T3b to be a great enhancement. We invite your comments. If you have any questions, concerns or comments, please contact us at 978-852-8584 or croenker@verizon.net.

Visit my web site at:
http://www.M1Bullpup.com" onclick="window.open(this.href);return false;

Re: REM T3b for the Black Ring Sight now on sale

Posted: 23 Oct 2009, 07:29
by M1P90
The REMT3b is now available for sale and I have them in stock!!

Come and get em!! :D

Re: REM T3b for the Black Ring Sight now on sale

Posted: 11 Nov 2009, 13:08
by Augustus
A couple questions : When mounted, does the wire / dial block the backup iron sights on the side that it is mounted on?
If I send you my optic, can you install the LED, then send it back to me for re-mounting?

Re: REM T3b for the Black Ring Sight now on sale

Posted: 11 Nov 2009, 20:41
by M1P90
The Wire does block the Back up iron sights for the side it is mounted.
I install the T3b to your Ring Sight for free.
Just send me your sight and tell me what color LED ( Red or Green or Blue ) you desire
You can go to my web site http://www.M1bullpup.com" onclick="window.open(this.href);return false; to order :thumb:

Re: REM T3b for the Black Ring Sight now on sale

Posted: 27 Jan 2010, 07:39
by M1P90
I now have the REM T3b in 3 colors. RED, GREEN and BLUE.

My web site is completed and back up and running. :monkey:

I now take visa, mastercard and discover along with paypal.

Check out my new line of "Peace Through Strength" merchandise. :D
http://www.M1Bullpup.com" onclick="window.open(this.href);return false;

Re: REM T3b for the Black Ring Sight now on sale

Posted: 27 Jan 2010, 08:13
by panzermk2
:thumb: Glad to here that you have gotten through all the CC Processor BS!

Re: REM T3b for the Black Ring Sight now on sale

Posted: 27 Jan 2010, 08:59
by f3rr37
Great looking website!

Re: REM T3b for the Black Ring Sight now on sale

Posted: 27 Jan 2010, 10:02
by panzermk2
Is that you chopping prior CC processors?

Re: REM T3b for the Black Ring Sight now on sale

Posted: 27 Jan 2010, 11:25
by M1P90
panzermk2 wrote:Is that you chopping prior CC processors?
:laugh: Got to take my frustration out on somthing! :wall:
May as well get some excercise and get wood for my wood stove at the same time. :thumb:

Re: REM T3b for the Black Ring Sight now on sale

Posted: 27 Feb 2010, 09:22
by freelienr
good gravy those are cool! I've seen the illumination before, but not in the green and blue. Love the blue, so cool looking.. and the green..and the red :laugh:
I used to have a scope that cycled through red and green, should have kept that :( .

M1, have considered making a multi-color version? When you turn the power from 1-11 it cycles a color for a section of power levels i.e.: Green for 1-4, Red for 5-8, Blue for 9-11. They make LEDs that can cycle colors correct?
Judging from the pictures you took blue is the brightest i imagine this makes it more effective in higher levels of light (or does it start to wash out on bright, lighter toned backdrops?)
Red looked like a good middle color and green seemed to keep a low yet visible level on #1 making it ideal for dark situations where you don't want to be blinded by your sight.

Or one that cycles through Green for 1-5 and Blue for 6-11 I would jump on that in a heart beat! Is that a possibility? :drool: